;========================= GSD file: PSMART053D.GSD =====================
;
;DEVICE NAME:       SMART
;DEVICE REVISION:   1.00
;VENDOR NAME:       Penko Engineering
;GSD REVISION DATE: 04-04-2002
;
;======================================================================

#Profibus_DP

GSD_Revision        = 1

;========================= PRODUCT SPECIFICATIONS =====================

Vendor_Name         = "Penko Engineering"
Model_Name          = "SMART"
OrderNumber         = "000000"
Ident_Number        = 0x053d
Revision            = "Rev. 1.00"
Hardware_Release    = "Rev. 1.00"
Software_Release    = "Rev. 1.00"
Bitmap_Device       = "PSMART053D"

;========================= OVERALL PROFIBUS SPECIFICATIONS ============
                              
FMS_supp            = 0
Protocol_Ident      = 0
Station_Type        = 0
Slave_Family        = 1

;========================= HARDWARE CONFIGURATION =====================

Implementation_type = "SPC3"
Redundancy          = 0
Repeater_Ctrl_Sig   = 0
24V_Pins            = 0

;========================= PROTOCOL CONFIGURATION =====================

Set_Slave_Add_supp  = 0
Auto_Baud_supp      = 1
Min_Slave_Intervall = 1
Freeze_Mode_supp    = 1
Sync_Mode_supp      = 1
Fail_Safe           = 0

;========================= SUPPORTED BAUDRATES ========================

9.6_supp            = 1
19.2_supp           = 1
45.45_supp          = 1
93.75_supp          = 1
187.5_supp          = 1
500_supp            = 1
1.5M_supp           = 1
3M_supp             = 1 
6M_supp             = 1
12M_supp            = 1

MaxTsdr_9.6         = 60
MaxTsdr_19.2        = 60
MaxTsdr_45.45       = 60
MaxTsdr_93.75       = 60
MaxTsdr_187.5       = 60
MaxTsdr_500         = 100
MaxTsdr_1.5M        = 150
MaxTsdr_3M          = 250
MaxTsdr_6M          = 450
MaxTsdr_12M         = 800

;========================= DIAGNOSTIC DEFINITIONS =====================

Max_Diag_Data_Len   = 32

;========================= PARAMETER DEFINITIONS ======================
                   
User_Prm_Data_Len   = 2
User_Prm_Data       = 0,1

;========================= MODULE DEFINITIONS =========================

Modular_Station     = 0
Max_Module          = 1

Max_Input_Len	      = 32
Max_Output_Len	      = 32
Max_Data_Len	      = 64
Modul_Offset         = 0                                             


Module = "SMART" 0x6A, 0x5F
; Inputs : double word, 32 bit signed integer, gross weight
;                 word, 16 status bits
;                 word, 16 command/reserved bits
;                 word, 16 inputs    1..16  
;                 word, 16 outputs 201..216
;                 word, 16 markers 401..416
;                 word, 16 markers 417..432
;          double word, 32 bit signed integer, extended register 1
;          double word, 32 bit signed integer, extended register 2
;          double word, 32 bit signed integer, extended register 3
;          double word, 32 bit signed integer, extended register 4
; Outputs:        word, 16 command/reserved bits
;                 word, 16 markers 969..984
;                 word, 16 markers 985..1000
;          double word, 32 bit signed integer, extended register 97
;          double word, 32 bit signed integer, extended register 98
;          double word, 32 bit signed integer, extended register 99
;          double word, 32 bit signed integer, extended register 100
;
; status bit definitation:
;  1 = hardware overload detected    
;  2 = overload detected             
;  3 = stable signal                 
;  4 = in stable range               
;  5 = zero corrected                
;  6 = center of zero                
;  7 = in zero range                 
;  8 = zero tracking posible         
;  9 = tare active                   
; 10 = preset tare active            
; 11 = new sample available          
; 12 = calibration invalid           
; 13 = calibration enabled           
; 14 = user certified operation      
; 15 = reserved
; 16 = reserved
EndModule




;======================================================================